For my new project, I am still working with the same concept with the blinking bracelet. During the in class critique, class mates recommended to make a bracelet that is unisex since my orginal bracelet was kind of masculine. I want this bracelet to fit comfortably for any man or woman, or child. I have…

Metal Head Purpose: A therapeutic head massager meant to give you the same creepy yet relaxed feel as the head massager. In the world of work and stress I believed people needed more ways to relax and this would be mostly focused on massaging the head. Inspiration Motions: The type of motions that I wanted…

 blinking lights bracelet.  soldered resistors and copper tape in back of bracelet.   testing LED’s with touch sensor and Arduino.  close up of back of bracelet. touch sensor with Arduino.

For my final project, I’d like to a simple replica of the windmill from Legend of Zelda: The Wind Waker! The first time I saw the motor in the class, for some reason, I immediately thought of windmills… so I guess it was meant to be! While this is a simple windmill, there are a…

Name-Ashley Villagrana Argumental names 1. “Chill Feeler”, 2. “Therapeutic Massager”, 3. “MetalHead+RelaxomaticShoulderCushion”, 4. “NewEnhancedWavelength(NEW)” or call it “(NEW) Feel” Materials: -3 motors? -3 toy servos? -Flexible wire from home depot. -Some Hard mendable wire from home depot. -Some really strong glue -Another Bread Board -Another switch. -Neck Pillow Purpose: To give another feel and edition…

For my final project proposal, I would like to continue off my first creative switch project of the LED land which I am very passionate about. I want this advanced on a much bigger scale physically as well as its functionality. So far I have these figurines of the Eiffel Tower, the Leaning Tower of…

Below I have the code, the pictures, and the video for the drawing device. Thank you for your help Sabrina, and I am sorry about  the misunderstanding in getting the other motors to run. I also have the video uploaded to dropbox as well as here. /*  * Force Sensitive Resistor Test Code  *  *…

Here is photo documentation of my wearables project. I sewed the holes on the corners of the Arduino to the piece of cloth, which was glued to the T-shirt.I had first taped down some the LED component and then sewed them on. The same was done for the switch. Unfortunately, the LEDs did not show…

This is the shiftout code, and a simple flexie force code. Paulina.  //**************************************************************// // Name : shiftOutCode, Dual One By One // // Author : Carlyn Maw, Tom Igoe // // Date : 25 Oct, 2006 // // Version : 1.0 // // Notes : Code for using a 74HC595 Shift Register // // :…

/*     ——————————————————— *     |  Arduino Experimentation Kit Example Code             | *     |  CIRC-05 .: 8 More LEDs :. (74HC595 Shift Register)   | *     ——————————————————— *  * We have already controlled 8 LEDs however this does it in a slightly * different manner. Rather than using 8 pins we will use just three * and an additional chip. * * *///Pin Definitions//Pin Definitions//The 74HC595 uses a serial communication //link which has three pinsint data = 2; int clock = 3;int latch = 4;//Used for single LED manipulationint ledState = 0;const int ON = HIGH;const int OFF = LOW;                        /* * setup() – this function runs once when you turn your Arduino on * We set the three control pins to outputs */void setup(){  pinMode(data, OUTPUT);  pinMode(clock, OUTPUT);    pinMode(latch, OUTPUT);  }/* * loop() – this function will start after setup finishes and then repeat * we set which LEDs we want on then call a routine which sends the states to the 74HC595 */void loop()                     // run over and over again{  int delayTime = 100; //the number of milliseconds to delay between LED updates  for(int i = 0; i < 256; i++){   updateLEDs(i);   delay(delayTime);   }}/* * updateLEDs() – sends the LED states set in ledStates to the 74HC595 * sequence */void updateLEDs(int value){  digitalWrite(latch, LOW);     //Pulls the chips latch low  shiftOut(data, clock, MSBFIRST, value); //Shifts out the 8 bits to the shift register  digitalWrite(latch, HIGH);   //Pulls the latch high displaying the data}/* * updateLEDsLong() – sends the LED states set in ledStates to the 74HC595 * sequence. Same as updateLEDs except the shifting out is done in software * so you can see what is happening. */ void updateLEDsLong(int value){  digitalWrite(latch, LOW);    //Pulls the chips latch low  for(int i = 0; i < 8; i++){  //Will repeat 8 times (once for each bit)  int bit = value & B10000000; //We use a “bitmask” to select only the eighth                                //bit in our number (the one we are addressing this time thro                    //ugh  value = value << 1;          //we move our number up one bit value so next time bit 7 will                    // be                               //bit 8 and we will do our math on it  if(bit == 128){digitalWrite(data, HIGH);} //if bit 8 is set then set our data pin high  else{digitalWrite(data, LOW);}            //if bit 8 is unset then set the data pin low  digitalWrite(clock, HIGH);                //the next three lines pulse the clock pin  delay(1);  digitalWrite(clock, LOW);  }  digitalWrite(latch, HIGH);  //pulls the latch high shifting our data into being displayed}//These are used in the bitwise math that we use to change individual LEDs//For more details http://en.wikipedia.org/wiki/Bitwise_operationint bits[] = {B00000001, B00000010, B00000100, B00001000, B00010000, B00100000, B01000000, B10000000};int masks[] = {B11111110, B11111101, B11111011, B11110111, B11101111, B11011111, B10111111, B01111111};/* * changeLED(int led, int state) – changes an individual LED  * LEDs are 0 to 7 and state is either 0 – OFF or 1 – ON */ void changeLED(int led, int state){   ledState = ledState & masks[led];  //clears ledState of the bit we are addressing   if(state == ON){ledState = ledState | bits[led];} //if the bit is on we will add it to le                    //dState   updateLEDs(ledState);              //send the new LED state to the shift register }

// OUTPUT: Use digital pins 9-11, the Pulse-width Modulation (PWM) pins // LED’s cathodes should be connected to digital GND int redPin = 9;   // Red LED,   connected to digital pin 9 int grnPin = 10;  // Green LED, connected to digital pin 10 int bluPin = 11;  // Blue LED,  connected to…

This is a turn on/off button I found, that I will be using to run my wearable design with a Reed sensor /* Button Turns on and off a light emitting diode(LED) connected to digital pin 13, when pressing a pushbutton attached to pin 2. The circuit: * LED attached from pin 13 to ground…